Four Locations to Better Serve You!
|
Post Drivers, Post Hole Diggers, & Other Fence Building Equipment at S & H Farm Supply Inc. with
four locations in Missouri.
Worksaver Post Drivers
Visit www.worksaver.com for more details.
|
If you have a small amount of fence to build or replace, then the HPD-20 is the product for you.
If you have a large amount of fence to build, then these drivers are ideal for terrain requiring
little alignment adjustment. The heavy duty adjusting base is built to withstand shock loads
drivers produce during operation. Both drivers use two manual adjustable, deep-threaded, plated
cranks. One crank adjusts the fore and aft positions. Another crank adjusts the side to side
positions. Grease zerks are located on all pivoting members.
| Model: |
HPD-20 |
| Maximum post size: |
8 3/4 in x 10 ft |
| Impact at full stroke: |
80,000 lbs |
| Impact at half stroke: |
40,000 lbs |
| Minimum tractor size: |
35 PTO HP |
| Rear hitch type: |
Cat. I and II |
| Drive cylinder size: |
2 in x 68 in |
| Operating range: |
50" to 128" |
| Tilt adjustment (front/back): |
10° from vertical |
| Tilt adjustment (side/side): |
17° from vertical |
|
Air Powered Post Drivers
|
Runs off any small air compressor that delivers at least 3.5 cubic feet of air at 70-100 PSI,
heavy duty construction, 60-75 strokes per minute - depending on model.
98E Basic
99E-M Driver - 2 and 7/8" Max Diameter, Recommended For Military Use and Drill Stem
99E-W Driver - 3 and 1/2" Max Diameter, Recommended For Highway Guide Post, Drill Stem
99E-X Driver - 2 and 1/4" Max Diameter, Recommended For Chain Link Fence
99E-Y Driver - 2 and 3/8" Max Diameter, Recommended For Chain Link Fence
|
Belltec Industries TM48 Post Hole Digger
Visit www.belltec.net for more details.
The Belltec TM48 Post Hole Digger mounts easily on three-point tractors with over
28 horsepower and have at least two hydraulic remote valves. Our machine's design
and performance go way beyond today's tractor mounted post hole diggers.
Belltec's system transforms a three-point tractor into a drilling machine capable of doing what
big truck rigs do: drill accurate, straight holes (to a depth of 5 ft on a single auger) in almost
any drilling condition, including solid rock and concrete.
If drilling holes is a problem for you, the TM48 is the solution. Whether it be hard, dry ground,
rocky soil or solid rock - it can drill it.
|
Bush Hog Post Hole Diggers
Visit www.bushhog.com for more details.
Easy To Replace Bolted Teeth, Replaceable Auger Points, Shear Pin or Shear Bolt Clutch
Protection, Bush Hog Gearbox With Machine Hardened Bevel Gears, Spring-Loaded Double Lip
Neoprene Seals, and One-Piece Pinions With Forged Input Shafts
| Model |
2101 |
2102 |
2103 |
| Tractor PTO |
540 RPM |
540 RPM |
540 RPM |
| Max Digging Depth |
48 inches |
48 inches |
48 inches |
| Type Hitch |
Category I |
Category I & II |
Category I & II |
| Component Protection |
Shear pin |
Shear bolt |
Slip clutch |
| Output Shaft |
2 inch diameter |
2 inch deameter |
2 inch diameter |
| Driveshaft Size |
ASAE Category I |
ASAE Category 3 |
ASAE Category 4 |
| Yoke |
2 7/8 inch tubing |
2 7/8 inch tubing |
2 7/8 inch tubing |
| Boom |
3 1/2 inch tubing |
3 1/2 inch tubing/reinforced ribs |
3 1/2 inch tubing/reinforced plates |
| Auger Selections w/ steel tip, single flighting |
6 inches |
6 inches |
6 inches |
| Auger Selections w/ bear claw point, single flighting |
9 inches |
9, 12 inches |
9, 12 inches |
| Auger Selections w/ bear claw point, double flighting |
9 inches |
9, 12, 15, 18, 24 inches |
9, 12, 15, 18, 24 inches |
| Options |
Leveling handle, parking stand, display stand, 8 and 12
inche extension kits |
Hyd. Down Force Pressure Kit
(adds 550 lbs of down pressure) |
N/A |
Optional |
Optional |
| Warranty |
1 year limited warranty, 5 year Gearbox Limited Warranty |
| |
|
|
|
|
|
